超硬材料工具是以金刚石或立方氮化硼作为切削刃主体的刀具。它们的硬度明显高于硬质合金,因此在淬硬钢、冷硬铸铁、粉末冶金、有色金属与非金属材料上,可以把原本依赖磨削的工序改为车削、铣削或铰削。理解它们的分类与边界,比记住型号更重要。

一、定义与分类

“超硬”是相对硬质合金而言。金刚石的显微硬度通常高于立方氮化硼,但两者都远高于硬质合金。需要提醒的是,金刚石在约 700 ℃ 以上且接触铁族元素时容易石墨化,因此不适合连续切削钢与铸铁;立方氮化硼耐热性更高、化学稳定性更好,是淬硬钢与铸铁的主力刃材。具体硬度与耐温随牌号、粒度与结合剂变化,选型时应以牌号技术资料为准。

按刃材、结构、形态与加工对象可作四种划分(见下表)。实际选型通常从“工件材料 + 硬度”入手,再匹配结构与刃型。

分类维度主要类别选型关注点
按刃材金刚石(单晶 / PCD / CVD)、立方氮化硼(整体 / 焊接 / 涂层)是否含铁族元素、工件硬度与耐热要求
按结构整体式、复合焊接式、涂层式、可转位刀片冲击大小、成本与刃口一致性
按形态车刀片、槽刀片、铣刀片、铰刀、旋铣刀片、异形件工序类型与机床接口
按对象淬硬钢、铸铁、粉末冶金、铝合金、碳化钨、复合材料材料与硬度区间

二、典型产品介绍

整体立方氮化硼刀片

整体聚晶结构,无焊接界面。以站内示例牌号为例,CBN 含量 90%、粒度 3 μm、倒棱 15°×0.25 mm。刃口一致性好,适合淬硬钢的连续与半连续车削,可多次转位。优点是抗热冲击优于焊接结构、耐磨性高;限制是单位刃口成本较高,强断续或大冲击工况下崩刃风险高于韧性牌号。与硬质合金相比,硬态加工可减少或省去磨削工序;与陶瓷相比,抗冲击性更好,但耐高温与化学稳定性略逊。

复合焊接 CBN 刀片

CBN 层焊接于硬质合金基体,刃口承担切削、基体提供支撑与韧性。适合中等断续的批量车削与常规槽加工,经济性优于整体式。限制在于焊接界面存在热应力,极端热循环下有脱焊风险,刃口可用深度也有限。与整体式相比,韧性更好、成本更低;与涂层硬质合金相比,硬态加工寿命更长,但小切深精加工的表面质量更依赖刃口钝化控制。

全贴面金刚石刀片

金刚石层覆盖整个刃面,导热系数高、摩擦系数低,不易产生积屑瘤。适用于碳化钨辊环、铝合金、石墨等材料的精加工,表面粗糙度低、耐磨性强。它不能用于铁族材料,抗冲击性弱于 CBN,不适合大余量粗加工。与硬质合金相比,寿命与表面质量优势明显;与单晶金刚石相比,抗冲击性更好、可做成可转位刀片,但刃口锋利度略低。

金刚石铰刀

多刃 PCD 铰刀,刃口研磨精度高、尺寸一致性好,可替代部分“钻—扩—磨”工序。适用于铝合金、铜合金与铸铁的高精度孔精加工,一次铰削即可获得较紧的尺寸公差与较低的表面粗糙度。限制是对前道底孔质量与余量分布敏感,修正孔形误差的能力弱于磨削。与硬质合金铰刀相比寿命更长;与珩磨、磨削相比效率更高,但对孔形误差的修正能力较弱。

三、页面如何按点击自动呈现内容

本站的产品内容采用“数据驱动、构建期预生成”的方式。用户在首页或产品中心点击某张产品卡片,浏览器打开的是已经生成好的产品页,而不是在访问时临时调用模型生成文案。这样做的原因是首屏速度、内容稳定与搜索引擎收录都更有保障。

触发条件:点击产品卡片打开对应产品页;点击品类卡进入按 CBN、PCD、非标定制筛选的列表页。每个产品都有独立网址,可直接分享。

展示字段:产品名称、英文编号、材料构成(CBN 含量、粒度、刃口处理)、适用材料与硬度区间、典型工序、优势、限制、与相关方案的对比、选型建议、应用案例与同类产品。字段来自同一份产品数据,新增产品只需增加一条数据并重新生成页面。

页面结构:面包屑 → 产品图与标题区(定位句、关键特性、咨询入口)→ 材料与结构特性 → 适用场景 → 优势与限制 → 对比表 → 选型建议 → 应用案例 → 同类产品 → 询价入口。

示例文案(整体 CBN 刀片):整体聚晶结构,刃口一致性好,适用于淬硬钢的重载粗加工与硬态精加工。材料构成:整体 PCBN,示例牌号 CBN 含量 90%、粒度 3 μm、倒棱 S01525。案例参考:20CrMnTi 齿轮(58–62 HRC)强断续车削,单刃加工 100–150 件(站内案例数据,实际寿命随工况变化)。

四、适用平台、内容范围与目标读者

内容面向本站官网(纯静态页面,无后端服务),范围是三个品类(CBN、PCD、非标定制)与现有 12 款产品,按清单逐项生成,一款一个页面、一份数据。目标读者包括工艺与刀具工程师、采购人员、经销商与海外客户:工程师关注材料与失效边界,采购关注对比与交付,经销商关注品类全貌,海外客户可切换英文阅读。

文中对比均为定性描述,不构成性能承诺;寿命数据来自站内既有案例,不代表其他工况。涉及具体零件时,建议提供材料、硬度、机床型号与目标节拍,由工程师匹配后试切确认。

如需进一步了解某一类产品的适用边界,可从 产品中心 进入对应品类,或在联系我们中说明工况获取选型建议。

Superhard tools use diamond or cubic boron nitride (CBN) as the cutting edge. Their hardness is far above carbide, so hardened steel, chilled cast iron, powder metallurgy parts, non-ferrous alloys and non-metallic materials can often be turned, milled or reamed instead of ground. Understanding the categories and their limits matters more than memorising model numbers.

1. Definition and classification

"Superhard" is relative to carbide. Diamond is generally harder than CBN, and both are far harder than carbide. Note that diamond tends to graphitise above roughly 700 °C in contact with ferrous elements, so it is not suitable for continuous cutting of steel or cast iron. CBN has higher heat resistance and better chemical stability, making it the main edge material for hardened steel and cast iron. Exact hardness and temperature limits vary by grade, grain size and binder; always follow the grade data sheet.

By edge material, tools fall into diamond (single crystal, PCD, CVD-coated) and CBN (solid, brazed, coated) families. By structure they are solid, brazed, coated or indexable inserts. By form they include turning, grooving and milling inserts, reamers, whirling inserts and special parts. By workpiece they cover hardened steel, cast iron, powder metallurgy, aluminium, tungsten carbide and composites. Selection usually starts from workpiece material and hardness, then moves to structure and edge geometry.

DimensionMain categoriesWhat to check
Edge materialDiamond (single crystal / PCD / CVD), CBN (solid / brazed / coated)Ferrous content, hardness, heat resistance
StructureSolid, brazed, coated, indexableImpact level, cost, edge consistency
FormTurning, grooving, milling, reaming, whirling, special partsOperation and machine interface
WorkpieceHardened steel, cast iron, powder metallurgy, aluminium, carbide, compositesMaterial and hardness range

2. Typical products

Monolithic CBN inserts

A solid polycrystalline body with no brazed interface. Taking the in-house example grade: 90% CBN, 3 μm grain, 15°×0.25 mm chamfer. Consistent edges suit continuous and semi-continuous turning of hardened steel with multiple indexes. Strengths include better thermal-shock resistance than brazed structures and high wear resistance; limits include higher cost per edge and higher chipping risk than tough grades under heavy interruption. Compared with carbide, hard turning may reduce or eliminate grinding; compared with ceramic, impact resistance is better while hot hardness is lower.

Brazed CBN inserts

A CBN layer brazed to a carbide body: the layer cuts while the substrate provides support and toughness. Well suited to batch turning and standard grooving with moderate interruption, and more economical than solid inserts. The brazed interface carries thermal stress and may debond under extreme cycling, and usable edge depth is limited. Compared with solid inserts, toughness is better and cost lower; compared with coated carbide, life in hard turning is longer, but surface quality in light finishing depends more on edge honing.

Full-face PCD inserts

The diamond layer covers the entire rake face, giving high thermal conductivity, low friction and good resistance to built-up edge. Suited to finishing of tungsten carbide rolls, aluminium alloys and graphite, with low surface roughness and strong wear resistance. Not for ferrous materials; impact resistance is lower than CBN and heavy roughing is not recommended. Compared with carbide, life and surface quality are clearly better; compared with single-crystal diamond, impact resistance is better and the insert is indexable, at a slight cost in sharpness.

PCD reamers

Multi-flute PCD reamers with accurately ground edges and consistent dimensions can replace part of the drill–bore–grind sequence. They suit precision hole finishing in aluminium, copper alloys and cast iron, achieving tight tolerance and low roughness in one pass. They are sensitive to pre-hole quality and stock distribution, and correct form errors less effectively than grinding. Compared with carbide reamers, life is longer; compared with honing or grinding, efficiency is higher but form correction is weaker.

3. How pages present content on click

Product content on this site is generated ahead of time from structured data. When you click a product card on the home page or in the product centre, the browser opens an already generated page rather than calling a model at visit time. This keeps first paint fast, content stable and pages indexable.

Triggers: product cards open the matching product page; category cards open filtered lists for CBN, PCD or custom solutions; search and filters land on the list page and then the detail page. Every product has its own URL that can be shared or scanned.

Fields shown: product name, English code, material composition (CBN content, grain size, edge preparation), workpiece material and hardness range, typical operations, strengths, limits, comparison with alternatives, selection guidance, application cases and related products. All fields come from one product data file; adding a product means adding one record and regenerating.

Page structure: breadcrumb → product image and title area (positioning line, key features, enquiry link) → material and structure → where it fits → strengths and limits → comparison table → selection guidance → application case → related products → enquiry.

Sample copy (monolithic CBN insert): A solid polycrystalline structure with consistent edges, suited to heavy roughing and hard-state finishing of hardened steel. Material: solid PCBN; example grade 90% CBN, 3 μm grain, S01525 chamfer. Case reference: interrupted turning of 20CrMnTi gears (58–62 HRC), 100–150 pieces per edge (in-house case data; actual life varies).

4. Platform, scope and audience

Content serves this static website with no backend. Scope covers three categories (CBN, PCD and custom solutions) and the current 12 products, generated one by one: one page and one data record per product. Audiences include process and tooling engineers, purchasing staff, distributors and overseas customers. Engineers focus on material limits, purchasing on comparison and delivery, distributors on the full range, and overseas customers can switch to English at any time.

Comparisons on this site are qualitative and are not performance guarantees. Life figures come from existing in-house cases and do not represent other conditions. For a specific part, provide workpiece material, hardness, machine model and target cycle time so an engineer can match edge geometry and grade and confirm by trial cutting.

To explore a category, start from the product centre, or describe your application via contact for selection advice.

返回 新闻资讯Back to news 咨询选型Ask for selection advice